输电铁塔四地脚螺栓塔脚板抗拉承载力试验与计算方法研究

针对架空输电线路铁塔中常用的四地脚螺栓塔脚板进行了抗拉承载力试验和理论计算方法研究。首先,选取8个试件进行塔脚板抗拉承载力试验研究,分析塔脚底板板厚及有无加劲板对塔脚板抗拉承载力的影响;其次,通过有限元模拟塔脚板的应力分布情况,并结合“塑性分析,弹性设计”的思想,提出了一种基于屈服线理论的四地脚螺栓塔脚板抗拉承载力计算公式;最后,与试验结果、有限元仿真结果、已有技术规定中的计算结果进行了对比。结果表明:建议公式与试验结果和仿真结果较为吻合,相关技术规定中的计算结果偏于保守,验证了本文建议公式的精确性;底板厚度和加劲板的作用对塔脚板承载力影响较大。研究结果可为输电铁塔四地脚螺栓塔脚板结构设计提供参考。     

梁柱简化模型在自立塔塔线体系动态响应中的适用性研究

对输电塔进行合理简化可以提高塔线体系动力学仿真的效率。本文给出自立塔梁柱简化模型的计算方法，并提出利用梁柱简化模型计算方法建立自立塔塔线体系整体模型，同时采用桁梁混合模型建立精细化塔线体系整体模型，对两种模型塔线体系静力特性及振型和固有频率等动力特性进行对比分析。以脱冰工况为例，采用生死单元技术将施加在输电线节点上的集中质量单元杀死来模拟脱冰，实现对塔线体系动力学响应的有限元模拟，研究塔线体系简化模型在动态响应中的适用性。结果表明，两种模型弯曲变形误差小，低阶的振型相同，固有频率值误差小，动力特性基本相同；脱冰工况下，自立塔节点位移和塔材内力时程曲线一致，在提高计算效率的情况下，能有效保证计算精度。     

有耗介质层上多导体传输线的电磁耦合时域分析方法

目前,针对空间电磁场作用有耗介质层上传输线的电磁耦合,仍缺乏有效的数值分析方法.因此,本文提出一种高效的时域混合算法,很好地解决了有耗介质层上传输线电磁耦合建模难的问题.首先,对经典传输线方程进行改进,推导了适用于有耗介质层上多导体传输线电磁耦合分析的修正传输线方程.然后,结合时域有限差分方法和相应插值技术,求解修正传输线方程,获得多导线及其端接负载上的电压和电流响应,并实现空间电磁场辐射与多导线瞬态响应的同步计算.最后,通过相应计算实例的数值模拟,与CST软件的仿真结果进行对比,验证了时域混合算法的正确性和高效性.     

周期性管柱信道的声波通信技术研究综述

井下声波通信技术利用周期性管柱信道实时传输声波数据，相比于其他通信方式，具有适应性好、复杂度低、传输效率高等优点，在随钻地质导向、油水井监测等方面有广阔的应用前景，是发展智能油田的关键技术之一。本文主要综述上世纪90年代以来关于信道物理模型、信道容量、声信号调制与接收方法等关键问题的研究历程，并对通信系统的设计要点与国内外相关产品的现场应用进行梳理，为后续的技术改进提供依据。     

传输线方程的高精度龙格−库塔数值求解方法

提出了一种求解传输线方程的高精度龙格-库塔(RK)方法。此方法在空间上采取高阶泰勒展开,提高了对空间微分的近似精度,减少了数值色散所带来的误差。与传统的时域有限差分法(FDTD)方法相比,在每波长采样数相同时,RK方法的计算精度更高。同时,根据Taylor模型,对外界平面波激励源进行离散,成功利用RK方法对外部场激励传输线进行求解,扩大了龙格-库塔方法在求解传输线方程时的应用范围。通过编程对平面波辐照下无限大地平面上的单导体与双导体的算例分别应用FDTD方法与RK方法进行了计算,验证了RK方法的正确性。结果表明同等计算条件下RK方法的计算精度更高。     

双曲冷却塔塔筒水平地震响应分析

为明确冷却塔在水平地震下的内力环向分布特征及内在原因,同时探究不同地震波时程与规范反应谱所得内力差异的原因,以某大型双曲冷却塔为例,在动力特性分析的基础上,通过反应谱方法和时程方法的水平地震响应计算及对比分析,对上述两个问题进行了研究。研究表明:由于仅侧弯振型对水平地震有贡献,而塔筒的侧弯振型和实际响应均表现为整体侧倾并伴随微弱的截面“流动”变形,这也使塔筒各内力的环向分布分别呈现正弦、余弦分布特征;其整体侧倾可类比于悬臂杆结构,塔筒子午向轴力FY、子午向弯矩MY、剪力FXY和扭矩MXY的环向分布可借助悬臂杆侧倾时截面正应力和剪应力分布来解释;而截面“流动”变形则决定了环向轴力FX和环向弯矩MX的环向分布;整体侧移显著而截面变形极小也使FY和FXY的幅值在塔筒中下部明显大于FX;由于冷却塔第1阶侧弯振型在水平地震响应中往往起绝对主导作用,因此可先对所选地震波计算得到其反应谱,对比第1阶侧弯振型周期对应的水平地震影响系数α值,即可初步推断不同时程及规范反应谱方法所得结果的大小关系。     

Research and Evaluation on Wear in Power-Shift Steering Transmission Through Oil Spectral Analysis with RKPCA Method

The most common methodology used in element concentration measurement and analyzing of wear particles is Atomic emission (AE) spectroscopy .The present paper presents an evaluation method on wear in po...     

Infinite family of transmission irregular trees of even order

Distance between two vertices is the number of edges in a shortest path connecting them in a connected graph $G$. The transmission of a vertex $v$ is the sum of distances from $v$ to all the other vertices of $G$. If transmissions of all vertices are mutually distinct, then $G$ is a transmission irregular graph. It is known that almost no graphs are transmission irregular. Infinite families of transmission irregular trees of odd order were presented in Alizadeh and Klav?ar (2018). The following problem was posed in Alizadeh and Klav?ar (2018): do there exist infinite families of transmission irregular trees of even order? In this article, such a family is constructed.     

Semilinear wave models with friction and viscoelastic damping

In this paper, we study the global (in time) existence of small data solutions to the Cauchy problem for the semilinear wave equation with friction, viscoelastic damping, and a power nonlinearity. We are interested in the connection between regularity assumptions for the data and the admissible range of exponents p in the power nonlinearity.     

Microstructural stability and age-hardening behavior of Re-added dual two-phase Ni3Al and Ni3V intermetallic alloys

The effect of Re addition on the microstructure and hardening behaviour of the dual two-phase Ni₃Al (L1₂) and Ni₃V (D0₂₂) intermetallic alloy was investigated by scanning electron microscopy, transmission electron microscopy and Vickers hardness test. The two-phase eutectoid microstructure accompanying the Re-rich precipitates were observed in the channel region of the alloys in which Re substituted for Ni but not in those in which Re substituted for Al and V. The concomitant addition of Nb (or Ta) with Re more stabilized the two-phase eutectoid microstructure and consequently more induced the fine precipitates in the channel region. The annealing at temperatures below the eutectoid temperature was necessary to induce the fine precipitates in the channel region and thereby result in the precipitation hardening. The fine precipitation in the channel region and related hardening was attributed to the alloying feature so that Re is soluble in the A1 (fcc) phase at high temperatures and becomes less soluble in the two intermetallic phases decomposed from the A1 phase at low temperatures.